UNGER 15436 RO Membrane Care and Protection 1L
Product description
The UNGER membrane maintenance solution 15436 is available in a 1-liter size for the maintenance of suitable RO membranes.
Features and application
Do not expose your UNGER RO system to frost! The UNGER RO membrane maintenance solution is intended solely for membrane maintenance, not as an antifreeze!
The membrane of the RO pure water filter system achieves its optimal service life with a regular flow of water or flushing.
If the UNGER HydroPower RO is not used for an extended period (at the latest from the 7th day), the membrane must be protected against blockage.
For this purpose, the UNGER membrane maintenance solution is available
You need one bottle (1 l) for each membrane. (For the RO40C, this is filter 2+3)
This preserves the current condition of the membrane and prevents reduced performance or failure after a long period of inactivity.
Alternatively, you can run the device for approximately 30 minutes once a week to flush the membranes.
To protect the membrane, proceed as follows:
1. Switch off the UNGER HydroPower RO and disconnect the power supply.
2. Drain the water from the HydroPower RO. To do this, unscrew all filter caps and open the pressure relief valve on the back of the HydroPower RO until no more water flows out.
3. Close the pressure relief valve and screw the yellow sealing cap onto the concentrate outlet.
4. Remove the pre-filter and resin filter cartridges and store them in a plastic bag.
5. Fill one bottle of UNGER membrane maintenance solution (1 l) into each of the two rear membrane tanks.
6. Fill the three tanks (#1 pre-filter + both membranes #2, #3) with tap water until all three tanks are filled to just below the top edge. Tank #4 can remain without water.
7. Screw all 4 tanks shut again.
The membranes are now protected and the UNGER HydroPower RO can be stored away.
Recommissioning the UNGER HydroPower RO:
1. Unscrew all 4 filter caps.
2. Drain the water. To do this, unscrew the yellow sealing cap and install the concentrate hose. Now open the pressure relief valve.
3. Insert the filters. Pay attention to the correct position.
4. Screw the caps back onto the tanks and start the system.
5. The membrane maintenance solution is automatically flushed out and the resin filter is protected by the bypass.
Determine the suitable filter and replacement parts
Match the exact system designation with the stated compatibility. Filter inserts, membranes, and resin refills perform different tasks and are not interchangeable at will. Schedule replacements and maintenance according to the operating instructions and the measured values of your system.

03 / GUT ZU WISSEN
FRAGEN? KLÄREN WIR.
UNGER 15436 RO Membrane Care and Protection 1L
Frag uns. Wir helfen dir weiter.Für welchen Einsatz ist UNGER 15436 RO- Membranpflegemittel Membranschutz 1l vorgesehen?
Das UNGER Membranpflegemittel 15436 wird in der 1-Liter-Ausführung zur Pflege geeigneter RO-Membranen angeboten.
Wie bleibt das Produkt bis zum nächsten Einsatz verwendbar?
Entnehmen Sie die Vorfilter- und Harzfilterkartuschen und lagern diese in einer Plastiktüte. 5.
Welche Komponente kannst du bei Verschleiß ersetzen?
Filtereinsätze, Membranen und Harzfüllungen übernehmen unterschiedliche Aufgaben und sind nicht beliebig austauschbar.
Welche Angaben brauchst du vor dem Filterwechsel?
Notiere die genaue Gerätebaureihe und die Bezeichnung des bisherigen Filtereinsatzes. Auch Bauform und Anschluss müssen übereinstimmen; die Marke allein reicht nicht aus.
Woran orientierst du den Wechselzeitpunkt?
Nutze die Wartungsvorgaben des Geräts und die dafür vorgesehenen Mess- oder Zustandsanzeigen. Ein pauschaler Zeitraum passt nicht zu jeder Wasserqualität und Nutzungsmenge.
Was gehört nach dem Einsetzen zur Kontrolle?
Führe die vom Gerätehersteller beschriebene Inbetriebnahme durch und kontrolliere die Verbindungen auf Dichtheit. Prüfe die vorgesehene Wasserqualität, bevor du mit der Reinigung beginnst.
Warum ist der Filtertyp wichtiger als eine ähnliche Größe?
Vorfilter, Membran und Mischbettharz übernehmen unterschiedliche Aufgaben. Wähle den Einsatz für die tatsächlich vorgesehene Filterstufe deines Systems.